folder Beavertail folder Honky-Dory folder Buffalo-Boat folder Dayak folder Drift-boat-info folder Flies Flures Lures folder Oar locks and Anchor systems folder Birds What-you-get.htm Stitch-and-Glue.htm index.htm
This was my first stab at a one man boat. I basically scaled down a Buffalo Boat so it was made with one sheet of plywood for the side panels. It was only abou 36" inches wide on the bottom. It rowed surprisingly well once you got into it. Bui after falling on my wet butt a few dozen times trying to get into it and out of it I took my Sawzall to it.
"The next one will be wider, lower and decked," I said to myself. And then the Dayak happened.
The Future of Drift BoatsFwiw my current direction is plywood still skinned in glass, but where (almost) nothing is glued. All parts screw together over either a gasket or a thick bead of roofer's caulk--so any and every part can be replaced. In the old days skid shoes were popular on the bottom. The idea was to replace the skid shoe periodically in order to protect the bottom panel, because that was glued to the ribs and nearly impossible to replace. That's the idea. Screw all parts together with Torx screws and (marine grade) caulk. Now you don't need a skid shoe. Just replace the bottom every ten years. Glass makes side panels so much stronger I'll glass them up. But they will NOT be glued at the seams. Everything will go together with screws and caulk. Has that boat been made? I'm working on it. In traditional framed boats, if a side panel gets hopelessly fractured it's hard to remove if it's been glued to the ribs. If everything goes together with Torx screws everything can come apart. In a jiffy. After 30 years of fiberglass work I'm heading back to all wood. Or close to it anyway. I might use a little glass here and there. Change is good. Change is more interesting. I'm interested in decked all-wood boats, with only a few (removable) interior bulkhead partitions. And no ribs'a no kind. The only good ribs are the barbequed kind. Think about it. Even if you build a low-sided square ended skiff, if it's decked you can still run Yankee Jim Canyon or Whitehorse rapids. It's low so the wind won't torture you on the Deschutes. A decked low-sided skiff could run the Grand Canyon. Tom Martin does it all the time with his little GEM. Plenty of storage below the deck. Comfortable seats and optional standing/casting braces on top. Open boats don't make sense to me anymore. The original McKenzie boats had high sides so an OPEN boat could run big water. But then they're wind sails. Then they're hard to get into and out of. It just doesn't make sense. Decked is where it's at. The Dayak convinced me of that. Blog Start
Do it your self wood fiberglass drift boat and white water dory plans
DIY Wood and Fiberglass Drift Boat Plans -- drift boat building -- online drift boat blueprints
The Honky Dory -- a wide white water dory
Beavertail: all around do anything boat well-suited to Fly Fishing, now as 15' or 17' feet
Buffalo Boat -- the smallest pickup truck boat that will hold three in the boat
Montana Riverboats Buffalo BoatThe buffalo is a standard 15' 48" wide driftboat chopped off at both ends. Unlike a Rapid Robert, which is pointed at one end, the Buffalo Boat is chopped off square at both ends. The idea was to build a short, lightweight pickup truck boat built from the fat business-only portions (the middle) of a standard boat. The Buffalo Boat is now going on 25 years old and still going strong. This one is sitting on a trailer, but the Buffalo Boat does fit nicely in the back of any standard size pickup. If you place it on top of a spare tire and drop the tailgate, it will even fit in the back of a small pickup. The boat pictured here is a high-sided, fully-rockered Buffalo Boat. You can challenge surprisingly difficult water with this boat. Many users, however, do choose to reduce the rocker by up to 3", and to cut the height of the side panels down by as much as 4" or so, in order to make a less wind-resistent skiff, suitable for fly fishing in non-white-water conditions.
MRB Dayak -- as fun as white water getsI love this little boat. Building plans and step-by-step instructions are not finished and perhaps never will be. The diagrams and dimensions are finished however. Experienced boat builders can plunge right in. Right now. Beginners should know there will be some problem-solving along the way. The important information is all there. But the step-by-step instructions are not. I'm 69 in 2017 and I've got other things to work on before I'm ...... So maybe it's best to think of this as a freeby add-on to the completed plan sets already available. This little boat sure is fun to row. I can do anything with it. Even head back upstream at times. You can hold it in fast water and turn on a dime. And it sure is stable, even in very big water. It's a great little white water boat, although I did flip in once, after dropping into an 8' foot hole sideways, like a fool, because I was trying to ferry away from a wave train and didn't see it coming.
DIY Stitch and Glue Drift Boat Building. Digital blueprints, online plans images diagrams and step by step instructions
One-off Wood/Fiberglass and All Fiberglass Constructionfour different boats
* How to copy another driftboat hull
* How to design and build your own hull from scratch
* How build a stitch and glue boat from someone else's framed-boat blueprints