What you get for $30 dollars is a password

There are a lot of public free-for-all pages here at Montana Riverboats. What is for sale is a password granting access to blocks of HTML pages, diagrams, images and step-by-step instructions for building three different boats--five boats actually, because two of the boats (Beavertail and Honky Dory) are documented in two different sizes.
meme_grand_IMG_0111
Grand HD
The only pages that do prompt for a password have the characters 'Ebook' or 'Diagrams' in the text of the link. I used to sell real paper blueprints paried with a ring-bound manual. Others still do that, for prices ranging from $150 dollars and up, for only one boat at a time..

From Montana Riverboats you get a password for $30 dollars, granting online acccess to three different boats coming as five individual plan sets--if you count the 15' and 17' foot size options available for both the Beavertail and the Honky Dory. There is even a fourth not-yet completed plan set (the Dayak) thrown in for free. Buy a password. Look things over.

Note too: The forum is a separate password. You have to create your own forum password by navigating to the forum and clicking the "Login or Register" button. The following is an example of a link that does prompt for a $30 dollar password:

(Honky Dory) Ebook-hd-15



Ask for a refund if you have buyer's remorse. I'm easy. I don't need a reason. Just a request. Good luck. Sandy.

Blog (click any images for a bigger view)

  Blog Start

 

Newer

 

2022-05-25-1610

Pmd-time

 

up-ztk_2022-05-25-04.51.54_DMap_pPmdinvise.jpg

2022-04-13-1137

Jellystone Nymph

This a top ten GOAT killer, high and low on the watershed.

 

jellystone.jpg
jellystone.jpg
jellystone.jpg
rubberleg-stitch.jpg
rubberleg-stitch.jpg
rubberleg-stitch.jpg
0-Rubberleg_Needle.jpg
0-Rubberleg_Needle.jpg
0-Rubberleg_Needle.jpg

2021-11-13-0726

Styrofoam skills

Will I live long enough to build everything? I doubt it. But still. I might be able to work the wider, trolling-motorized SUP board in.

This is a guy making a surf board but the skills and the tools would be much the same.

https://www.youtube.com/watch?v=rYYuDt8Z2cY

styrofoam skills

2021-09-19-1606

Two days later

up-up-deck-donut.jpg I'll probably have to carve into at least one of those bulkheads when making room for passenger's feet. I'll keep those foot wells a good 12" inches off the floor, so they'll be easier to drain.

2021-09-13-1025

Deck Donut

up-up-ddonut.jpg The deck donut--now bottom side up, getting a bit of fiberglass reinforcement. The rest of the deck will hinge up and down onto this perimeter, over the seat wells and over a 2" inch thick foam gasket.

2021-09-09-0518

Bill fish

That's my buddy Bill yesterday, catching a small cutthroat on a home made bamboo fly rod. Bill gets $2500 each for his rods and his orders are a year out right now. This one's 5wt. Damn nice rod. It almost casts itself, and you can reach out to 60' feet if you want. No problem. up-billfish.jpg

2021-08-09-1927

SockeyeShiner

Sockeye Shiner Streamer

In late summer when the fishing is slow many resort to beetles and tiny hoppers. I like big hoppers, even in late summer. For streamers on the other hand, at least when it's bright and hot I like small. This one is tied on a #14 wet fly hook.

2021-07-28-0533

Homemade Scarfer

homemade plywood scarfer Cut a piece of particle board 24" inches by 16" inches. Glue a 2x4 to one 24" inch edge. Now angle the edge so a 7-1/4" inch saw bolted onto that angled edge almost but not quite cuts all the way through 1/2" plywood. For an 8-1/4" saw you can set to cut all the way through.

Here's the not obvious part: You have to be super careful and precise when mounting the saw. You want the saw absolutely dead parallel or you might even want to mount the saw ever so slightly not parallel so the front, leading edge of the blade is dead flush to the particle board edge while the rear tailing edge of the blade perhaps 1/5th the width of the blade away from the particle board.

If the saw ends up mounted not parallel to the particle board, so the leading edge of the blade is not dead flush the saw will gradually migrate downward as you cut, and eventually it will bind.

To scarf two four foot plywood edges together--to make a longer panel--put the plywood down on a firm flat surface a few feet up from the floor. Clamp a straight edge approximately 16" inches back (trial and error will give the exact measurment, which you can then remember) from the edge you want to cut. Now run the saw with the particle board foot pressed tightly against the straight edge. The massive weight of all that particle board keeps the saw from shaking. With a freshly sharpened blade you'll get a baby smooth cut.

This is a 7-1/4" inch saw, which are the most common. An 8-1/4" saw is a bit better suited. I recently hacked an old 8-1/4" inch saw so it takes a 10" blade. The longer the blade the longer the scarf. And the longer the scarf the stronger the scarf. Older

  Blog Start

 

(MRBHome)/What-you-get.htm