Overview folder Beavertail folder Honky-Dory folder Buffalo-Boat folder Dayak folder Whale Rider folder Drift-boat-info folder Flies Flures Lures folder Oar locks and Anchor systems What-you-get.htm folder Blog Stitch-and-Glue.htm index.htm
MRB BlogBlog Start
Newer (move up)
Homemade ScarferCut a piece of particle board 24" inches by 16" inches. Glue a 2x4 to one 24" inch edge. Now angle the edge so a 7-1/4" inch saw bolted onto that angled edge almost but not quite cuts all the way through 1/2" plywood. For an 8-1/4" saw you can set to cut all the way through.
Here's the not obvious part: You have to be super careful and precise when mounting the saw. You want the saw absolutely dead parallel or you might even want to mount the saw ever so slightly not parallel so the front, leading edge of the blade is dead flush to the particle board edge while the rear tailing edge of the blade perhaps 1/5th the width of the blade away from the particle board.
If the saw ends up mounted not parallel to the particle board, so the leading edge of the blade is not dead flush the saw will gradually migrate downward as you cut, and eventually it will bind.
To scarf two four foot plywood edges together--to make a longer panel--put the plywood down on a firm flat surface a few feet up from the floor. Clamp a straight edge approximately 16" inches back (trial and error will give the exact measurment, which you can then remember) from the edge you want to cut. Now run the saw with the particle board foot pressed tightly against the straight edge. The massive weight of all that particle board keeps the saw from shaking. With a freshly sharpened blade you'll get a baby smooth cut.
This is a 7-1/4" inch saw, which are the most common. An 8-1/4" saw is a bit better suited. I recently hacked an old 8-1/4" inch saw so it takes a 10" blade. The longer the blade the longer the scarf. And the longer the scarf the stronger the scarf.
Belt SanderBelt sander finally got useful. I need to rebuild the frame so I can sand curved parts with the front end of the sander. Today was a tool building day. Scarfer comes next.
Cardboard deck rimThe cardboard might not be strong enough.
I might have to replace it with plywood and fiberglass. We'll see. This (the cardboard pattern) is the outer rim of a two or maybe three part deck. The inner deck section(s) will bolt down onto the perimeter rim over a 1" inch thick foam gasket, so wave crashing can't swamp the boat and sink it.
The whole inner section(s) will hinge up and down (in one or maybe two parts) so you can store coolers and camping gear below, without having to fight with a rabbit warren of hatch covers that are never big enough. Most of the visible cross braces shown here are only temporary. Progress happens. Slowly.
Whale Rider:A vid from last week Older (move down)
Do it your self wood fiberglass drift boat and white water dory plans and step-by-step building instructions
DIY Wood and Fiberglass Drift Boat Plans -- drift boat building -- online drift boat blueprints
The Honky Dory -- a wide white water doryNow as a 15' foot or 17' foot boat The Honky Dory is more of a white water boat than the Beavertail. The Honky Dory is wide and stable in big water -- the 15' foot version (made from 16' foot side panels) is 56" inches wide under the oarlocks. Like most traditional Oregon-style boats the Honky Dory is wide up front too. Stitch and glue construction is assumed although all included plans can be adapted to traditional framed dory construction techinques. But unlike Oregonstyle boats the HD has a small front deck and movable/adjustable seats so the payload can be shifted forward enough to accommodate an additional fisherman behind the rower.
Beavertail: all around do anything boat well-suited to Fly Fishing, now as 15' or 17' feet
The Beavertail is an easy rowing day trip fly fishing guide boat. It turns well and holds well. Most important, the Beavertail trims properly with a husky passenger seated behind to rower.Not many boats--from any manufacturer or builder--can make that claim. All Boat Plans are offered online honly -- in other words what you get is a password to otherwise hidden portions of the website. As such there are no blueprints per se. Everything is offered online.
Buffalo Boat -- the smallest pickup truck boat that will hold three in the boat
Montana Riverboats Buffalo BoatThe buffalo is a standard 15' 48" wide driftboat chopped off at both ends. Unlike a Rapid Robert, which is pointed at one end, the Buffalo Boat is chopped off square at both ends. The idea was to build a short, lightweight pickup truck boat built from the fat business-only portions (the middle) of a standard boat. The Buffalo Boat is now going on 25 years old and still going strong. This one is sitting on a trailer, but the Buffalo Boat does fit nicely in the back of any standard size pickup. If you place it on top of a spare tire and drop the tailgate, it will even fit in the back of a small pickup. The boat pictured here is a high-sided, fully-rockered Buffalo Boat. You can challenge surprisingly difficult water with this boat. Many users, however, do choose to reduce the rocker by up to 3", and to cut the height of the side panels down by as much as 4" or so, in order to make a less wind-resistent skiff, suitable for fly fishing in non-white-water conditions.
MRB Dayak -- as fun as white water getsI love this little boat. Building plans and step-by-step instructions are not finished and perhaps never will be. The diagrams and dimensions are finished however. Experienced boat builders can plunge right in. Right now. Beginners should know there will be some problem-solving along the way. The important information is all there. But the step-by-step instructions are not. I'm 69 in 2017 and I've got other things to work on before I'm ...... So maybe it's best to think of this as a freeby add-on to the completed plan sets already available. This little boat sure is fun to row. I can do anything with it. Even head back upstream at times. You can hold it in fast water and turn on a dime. And it sure is stable, even in very big water. It's a great little white water boat, although I did flip in once, after dropping into an 8' foot hole sideways, like a fool, because I was trying to ferry away from a wave train and didn't see it coming.
DIY Stitch and Glue Drift Boat Building. Digital blueprints, online plans images diagrams and step by step instructions
One-off Wood/Fiberglass and All Fiberglass Construction
- Dimensions and instructions for five different boats
- How to hull
- How to design and build your own hull from scratch
- How build a stitch and glue boat from someone else's framed-boat blueprints