The future of drift boats and river skiffs

Fwiw my current direction is plywood still skinned in glass, but where (almost) nothing is glued. All parts screw together over either a gasket or a thick bead of roofer's caulk--so any and every part can be replaced. In the old days skid shoes were popular on the bottom. The idea was to replace the skid shoe periodically in order to protect the bottom panel, because that was glued to the ribs and nearly impossible to replace.

That's the idea. Screw all parts together with Torx screws and (marine grade) caulk. Now you don't need a skid shoe. Just replace the bottom every ten years. Glass makes side panels so much stronger I'll glass them up. But they will NOT be glued at the seams. Everything will go together with screws and caulk.

Has that boat been made? I'm working on it. In traditional framed boats, if a side panel gets hopelessly fractured it's hard to remove if it's been glued to the ribs. If everything goes together with Torx screws everything can come apart. In a jiffy.

After 30 years of fiberglass work I'm heading back to all wood. Or close to it anyway. I might use a little glass here and there.

Change is good. Change is more interesting. I'm interested in decked all-wood boats, with only a few (removable) interior bulkhead partitions. And no ribs'a no kind. The only good ribs are the barbequed kind.

Think about it. Even if you build a low-sided square ended skiff, if it's decked you can still run Yankee Jim Canyon or Whitehorse rapids. It's low so the wind won't torture you on the Deschutes. A decked low-sided skiff could run the Grand Canyon. Tom Martin does it all the time with his little GEM.

Plenty of storage below the deck. Comfortable seats and optional standing/casting braces on top. Open boats don't make sense to me anymore. The original McKenzie boats had high sides so an OPEN boat could run big water. But then they're wind sails. Then they're hard to get into and out of. It just doesn't make sense.

Decked is where it's at. The Dayak convinced me of that.

How about a RIB (rigid inflatable boat) river skiff? Or would it RIB river raft? Anyway, same idea as an RIB yacht dingy but the bottom is river skiff profiled. A hard bottom for stiffness but permanently attached inflatable tubes for secondary stability, rock bumping, and reserve buoyancy. The tubes don’t do much of anything in flat water but, they make the boat perform like a raft in big waves.
I’ve been wondering how to go about building that prototype…

Sounds good. Like a Zodiac River Dory? That would be cool too.

There are some boat builder Rendevous events that don't allow anything but pure wood. No glass. No Plascore etc
All wood and screws only. Pretty awesome

I am moreso going in the opposite direction, towards corecell. I have built a lot of plywood and strip boats, and they last great, but they need someone who "gets it", and isn't sick, divorced, or otherwise distracted to take care of them as they should be.

I was in a major accident and had to replace 10 feet at the back of my sailboat because before the accident, I left a pihi held in with drywall screws. Water got in. I didn't get back at it fo 5 years. The whole rear deck and cockpit had to be remade. I was OK with that as I do that kind of thing. But plastic boats can tolerate an owner with minimal skills.

Different deal. I'm sixty and some day everything will belong to my daughters. It's not looking good. :)

One thing I have done is run keels or strips out of solid epoxy and glass. I use that technique plasterers use where they put in place an alignment strip, then run a mold (plywood cutout), sculpting plaster into a crown molding, or whatever. Takes several shots, but you get a solid epoxy stringer, or keel. I glass that, then I can run screws holding aluminum flat into the epoxy without any risk of water getting into the plywood skin. It will take some wear.

If I can get it, I will use solid pulltruded fiberglass for the rub strips.

Keep us posted. Images are cool. I need to learn how to do video in my old age